SouthernTrader 20 Posted May 28, 2019 Hi guys, Hoping someone can help me out here. I’ve got a BMW 118d, done 90k, just had a new LUK clutch and DMF as the last one was noisy. customer has reported a vibration right at the top of the clutch. Got it back in and there is a vibration felt through the clutch right at the very top of the biting point. Changes gears fine and no noise now but just this vibration. If you sit at idle it’s most noticeable right at the top - just as you are dipping the clutch or bringing it up to bite Anyone got any suggestions? Any help is much appreciated. Apologies if my description is poor! Share this post Link to post Share on other sites
Row 71 Posted May 28, 2019 1 hour ago, tradex said: Sounds more like a thrust bearing issue to my uneducated mind? Agree , I hope you changed the bearing when you did the clutch/dmf Share this post Link to post Share on other sites
SouthernTrader 20 Posted May 28, 2019 Hi there, yep it’s had a new release bearing as part of the clutch change Weird thing is it’s a very similar feel to when a release bearing is on its way out Share this post Link to post Share on other sites
Mojo121 229 Posted May 28, 2019 Possible the new part is defective. Is happening more and more nowadays. Share this post Link to post Share on other sites
TangoVictor32 90 Posted May 28, 2019 (edited) 4 hours ago, Mojo121 said: Possible the new part is defective. Is happening more and more nowadays. This or maybe the mechanic left something lose or even left something in there - it can happen! (There was a case of a surgeon leaving some equipment inside of someone!) Edited May 28, 2019 by TangoVictor32 Share this post Link to post Share on other sites
BHM 994 Posted May 29, 2019 9 hours ago, Mojo121 said: Possible the new part is defective. Is happening more and more nowadays. Have you ever known a brand new clutch/DMF defective? When I had one that I suspected was defective I was told by a couple of garages they’ve never seen one & a few members of this forum said the same & suggested it was something else. 400 miles later the gearbox ate itself. Share this post Link to post Share on other sites
Mojo121 229 Posted May 29, 2019 2 hours ago, BHM said: Have you ever known a brand new clutch/DMF defective? When I had one that I suspected was defective I was told by a couple of garages they’ve never seen one & a few members of this forum said the same & suggested it was something else. 400 miles later the gearbox ate itself. Not personally but a garage we use said they’ve had bad wheel bearings, sensors and a spring that went bang an hour after being fitted. Maybe not the clutch or flywheel plates but the bearing is possible. I wonder whether it’s worth driving the car and riding the clutch a little, see if some wear/ use will sort it out? Share this post Link to post Share on other sites
David Horgan 564 Posted May 29, 2019 Clutch has to be lined up properly when fitted ? Or it shakes Flywheel bolts tightened properly ? New Bolts ? New release Bearing fitted properly ? It was changed ?" Just a thought Might be a silly thought " But they did change the flywheel ? " one hopes . Things have been left in silly places as suggested , seen that many times . Annoying though isn't it when you've done the right thing 1 Share this post Link to post Share on other sites
SouthernTrader 20 Posted May 29, 2019 Yep, David that’s my feeling. Spent a good chunk of money replacing the parts and now I’m back to square one. I’m going to get it back to the mechanic for another look and hopefully it’s just something simple - rarely is though I find! thanks for the input guys Share this post Link to post Share on other sites
Dave2302 387 Posted May 29, 2019 (edited) Bad DMF / Clutches happen once in a while, even with LUK !! I will not fit any other make these days, LUK are OEM for most Car Manufacturers so they are good enough for me. I'd say over the years of doing LUK clutches / DMF 2 or 3 have been bad, usually Concentric Bearing failures shortly after doing them, . Garage who fitted it will just have to do the whole job again, clearly a warranty issue. All above suggestions also apply.................... Like Fitter has left his I phone in their when the glue on his face let go etc etc If the mechanic says anything other than "Yes no problem I'll tear it apart again if I have to" then you need another mechanic !! Shit Happenz Edited May 29, 2019 by Dave2302 Share this post Link to post Share on other sites
It's me 615 Posted May 29, 2019 47 minutes ago, Dave2302 said: Happenz i know a web page for that Share this post Link to post Share on other sites
Stalker 180 Posted May 29, 2019 In any case the gearbox will have to come back out. The release bearing comes with all clutch kits on these, however it doesnt always come with a new clutch arm/fork. Is the fork ok? Faulty flywheels so soon after replacement can be attributed to another fault elsewhere. Share this post Link to post Share on other sites
TangoVictor32 90 Posted May 29, 2019 17 hours ago, BHM said: Have you ever known a brand new clutch/DMF defective? When I had one that I suspected was defective I was told by a couple of garages they’ve never seen one & a few members of this forum said the same & suggested it was something else. 400 miles later the gearbox ate itself. Any brand new item can be defective. There is a very low chance but every item has possibility to be faulty. Whether 1 in 1000 or 1 in 10000 it does happen 1 in 10 if its from euros Was it even the correct one? Euros are known to send out wrong parts. "Oh there's 2 filters listed" why 2? If so you should know which one my car needs!! They do play parts darts Share this post Link to post Share on other sites
MattR 177 Posted June 1, 2019 Take it back to the guy who fitted it. Hopefully its a 'no problem, I'll sort it ' mechanic. Share this post Link to post Share on other sites
SouthernTrader 20 Posted June 3, 2019 Just an update on the situation. Mechanic stripped it out and fitted a new LUK clutch and flywheel and now it’s perfect - no vibration at all. can only assume the parts were faulty even though I’m told it’s very rare. old parts are going back for a refund so not a bad outcome in the end. Share this post Link to post Share on other sites
It's me 615 Posted June 3, 2019 this is why its always best buying high value items from the local factor well done ,sweat over i ordered a complete kit for a customer last year for a sprinter,it arrived and because i had taken the customers word that the original engine was fitted turns out it wasnt so kit wrong,fortunately i had used pages so i didnt pay the 10% return fee for wrong parts ordered special Share this post Link to post Share on other sites
